Boxtec Onlineshop SupportKontaktPlayground
 Advanced Search
My Account  Cart Contents  Checkout  
  Top » Catalog » Microcontroller » Accessories » Time » 53040 My Account  |  Cart Contents  |  Checkout   
Categories
E-Textiles (29)
Electronics (675)
Microcontroller (670)
  Android (1)
  Arduino Boards (36)
  ARM (20)
  ATtiny Boards (7)
  AVR (19)
  Beginner Kits (5)
  Camera (6)
  Digispark (13)
  Diverse (4)
  Drones (5)
  Feather Boards (2)
  IoT (12)
  Kits (30)
  PIC (11)
  Power supply (42)
  Programmer (13)
  Propeller
  Robotics (13)
  Shield/Breakout (139)
  Teensy (11)
  VoIP (1)
  Wireless (99)
  Accessories (181)
    Adapter Boards (1)
    Breadboards (15)
    Breakout Boards (27)
    Cables (32)
    Cases (20)
    Connectors (28)
    Diverse (8)
    Interface (33)
    Proto Boards (8)
    Storage (5)
    Time (4)
Sensors (204)
Tools (138)
Diverse (64)
Specials
Newest Products   
Auction Products
Goto...
Manufacturers
What's New? more
Liquid Pump - 3V
Liquid Pump - 3V
CHF 6.20
Information
Shop News
Shipping & Returns
Privacy Notice
Terms & Conditions
FAQ
Contact Us
Follow us on Twitter
Visa, Mastercard, Paypal, Bitcoin, Invoice
Adafruit TPL5111 Low Power Timer Breakout
[53040]
CHF 7.20
CHF 5.85
  Valid through : 12/31/2019
This product will be retired from our catalogue once it goes out of stock. It is only available in the quantity listed. 

Stock: 2

With some development boards, low power usage is an afterthought. So what should you do when it's time to turn around and make that project of yours run on a battery or solar?

The Adafruit TPL5111 Reset Enable Timer is a stand-alone breakout that will turn any electronics into low-power electronics! It will take care of enabling & disabling your electronics using a built in timer that can vary from once-every 100ms up to once every two hours. Basically, the TPL will set an enable pin high periodically, adjustable by potentiometer or resistor, and turn on your project's power. It will then wait until a signal is received from the project to tell the TPL that it can safely disable the project by setting the enable pin low.

Usage is easy. First, set your desired delay but adjusting the on-board trim pot: all the way to the left is once-per-100ms and all the way to the right is once-every-2-hours. Then, connect VDD up to your 3-5V project power supply, and then your project's enable pin to the Enable pin. Finally, select a signal pin from your project to the Done pin. In your project's code or design, just make sure that it sets the Done pin high once it is completed with its task. That's it!

While the TPL5111 is running (but the remainder of the project is de-powered) the current draw is about 20uA (according to our Monsoon Power Meter).

If you want to turn the device on by hand, you can also activate the TPL by pressing the onboard tactile switch (or wire your own switch to the Delay pin).

Documents:

This product was added to our catalog on Tuesday 12 September, 2017.
Customers who bought this product also purchased
USB-A Adapter Board
USB-A Adapter Board
NeoPixel Ring - 16 x WS2812B 5050 RGB LED
NeoPixel Ring - 16 x WS2812B 5050 RGB LED
Mini Momentary Push Button Switch (red) - 6x6mm
Mini Momentary Push Button Switch (red) - 6x6mm
8-Bit Parallel-In/Serial-Out Shift Register (74HC165N)
8-Bit Parallel-In/Serial-Out Shift Register (74HC165N)
EMAX ES3001 Analog Servo 43g
EMAX ES3001 Analog Servo 43g
Magnetic Buzzer - 12mm 2.048kHz
Magnetic Buzzer - 12mm 2.048kHz
Shopping Cart more
0 items
Manufacturer Info
Adafruit
Adafruit Homepage
Other products
Notifications more
NotificationsNotify me when this item is restocked Adafruit TPL5111 Low Power Timer Breakout
Tell A Friend
 
Tell someone you know about this product.
Reviews more
Write ReviewWrite a review on this product!
Languages
Deutsch English

Copyright © 2019 Boxtec Onlineshop
Powered by BlueOnyx

Links to partners, friends and other worthwile sites:
Grafik Burri 2