THE SHOP IS CLOSED NOW!

This is an httrack archive of shop.boxtec.ch, it will be kept online as reference until March 2022 at least.
If you need access to datasheets and product information after that, please download the complete archive (1.9G) via bittorrent.


Boxtec Onlineshop SupportKontaktPlayground
My Account  Cart Contents  Checkout  
  Top » Catalog » Microcontroller » Wireless » RF » 50615 My Account  |  Cart Contents  |  Checkout   
Categories
E-Textiles (5)
Electronics (445)
Microcontroller (335)
  Arduino Boards (8)
  ARM (1)
  ATtiny Boards (7)
  AVR (17)
  Beginner Kits (5)
  Camera (3)
  Digispark (11)
  IoT (5)
  Kits (22)
  PIC (6)
  Power supply (19)
  Programmer (8)
  Robotics (9)
  Shield/Breakout (65)
  Teensy (17)
  Wireless (27)
    Bluetooth (6)
    GPS (1)
    GSM/GPRS (3)
    Infrared (2)
    LoRa (3)
    RF (3)
    RFID (4)
    WiFi (4)
    ZigBee/XBee (1)
  Accessories (105)
Sensors (90)
Tools (70)
Diverse (49)
Specials
Newest Products   
Auction Products
Manufacturers
What's New? more
LPS8 Indoor LoRaWAN Gateway
LPS8 Indoor LoRaWAN Gateway
CHF 126.80
Information
Shop News
Shipping & Returns
Privacy Notice
Terms & Conditions
FAQ
Contact Us
Follow us on Twitter
Visa, Mastercard, Paypal, Bitcoin, Litecoin, Invoice
LoRa Shield - 868MHz v1.4
[50615]
CHF 21.90

Product retired

This product has been retired from our catalogue and is not available for odering anymore. The page is being kept for those looking for datasheets, sample code or other information.

 

Stock: 0

This is the new and improved v1.4 of Dragino's LoRa shield. The new version comes with an SMA female antenna connector and allows you to select GPIOs with jumpers, also in v1.3 the 3.3V LDO for powering the shield was removed and the 3.3V pin from the Arduino board is used now.

The Dragino LoRa Shield is a long range transceiver on a Arduino shield form factor and based on open source library. The LoRa Shield allows the user to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimising current consumption.

The LoRa Shield is based on RFM95W/RFM98W and targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, smartphone detection, building automation and so on.

Using Hope RF’s patented LoRa(TM) modulation technique the LoRa Shield can achieve a sensitivity of over -148dBm using a low cost crystal and bill of materials. The high sensitivity combined with the integrated +20 dBm power amplifier yields industry leading link budget making it optimal for any application requiring range or robustness. LoRa(TM) also provides significant advantages in both blocking and selectivity over conventional modulation techniques, solving the traditional design compromise between range, interference immunity and energy consumption.

These devices also support high performance (G)FSK modes for systems including WMBus, IEEE802.15.4g. The LoRa Shield deliver exceptional phase noise, selectivity, receiver linearity and IIP3 for significantly lower current consumption than competing devices.

Features:

  • Compatible with 3.3V or 5V I/O Arduino Board
  • Frequency Band: 868 MHz
  • Low power consumption
  • Compatible with Arduino Leonardo, Uno, Mega, Due
  • External Antenna via SMA female connector (antenna is included)

Specifications:

  • 168 dB maximum link budget
  • +20 dBm - 100 mW constant RF output
  • +14 dBm high efficiency PA
  • Programmable bit rate up to 300 kbps
  • High sensitivity: down to -148 dBm
  • Bullet-proof front end: IIP3 = -12.5 dBm
  • Excellent blocking immunity
  • Low RX current of 10.3 mA, 200 nA register retention
  • Fully integrated synthesizer with a resolution of 61 Hz
  • FSK, GFSK, MSK, GMSK, LoRaTM and OOK modulation
  • Built-in bit synchronizer for clock recovery
  • Preamble detection
  • 127 dB Dynamic Range RSSI
  • Automatic RF Sense and CAD with ultra-fast AFC
  • Packet engine up to 256 bytes with CRC
  • Built-in temperature sensor and low battery indicator

Changelog:

  • Lora Shield v1.0: The first hardware release for the Lora Shield.
  • Lora Shield v1.2: Connect the DIOs to Arduino IO. Change i-pex connector to SMA connector.
  • Lora Shield v1.3: Remove 5V to 3.3V LDO, use 3.3V directly from Arduino +3.3V pin.

Documents:

Replaces: 50614

This product was added to our catalog on Tuesday 10 May, 2016.
Customers who bought this product also purchased
LT-22222-L LoRa I/O Controller
LT-22222-L LoRa I/O Controller
LG308 v2 Indoor LoRaWAN Pico Gateway - 868MHz
LG308 v2 Indoor LoRaWAN Pico Gateway - 868MHz
LSN50 - Waterproof LoRa Sensor Node (M12)
LSN50 - Waterproof LoRa Sensor Node (M12)
EC25-E LTE Module for Dragino LGxx
EC25-E LTE Module for Dragino LGxx
MEMS Microphone Breakout - INMP401 (ADMP401)
MEMS Microphone Breakout - INMP401 (ADMP401)
Tool Kit - Screwdriver and Bit Set
Tool Kit - Screwdriver and Bit Set
Shopping Cart more
0 items
Manufacturer Info
Dragino
Dragino Homepage
Other products
Notifications more
NotificationsNotify me when this item is restocked LoRa Shield - 868MHz v1.4
Tell A Friend
 
Tell someone you know about this product.
Reviews more
Write ReviewWrite a review on this product!
Languages
Deutsch English

Copyright © 2022 Boxtec Onlineshop
Powered by BlueOnyx

Links to partners, friends and other worthwile sites:
Makerspace Reinach 1